Plastic Pit Setter for Moderate to Cold Climates

For 3/4" Meters

How To Order A Plastic Pit Setter

To order a Plastic Pit Setter, answer each of the following questions to create a Catalog Number for the Plastic Pit Setter that meets your setting requirements.

Example: PSBH-322-20-72-NL = a standard single lid style plastic pit setter with an inlet angle ball valve inlet, outlet angle check valve, for a 3/4" meter, inlet connection for flared copper, outlet connection for flared copper and a pit diameter and depth of 20"x72".

What type of pit setting is required?

  Setting Type Code
  Standard for Single Lid Cover PS
  Standard for Double Lid Cover PD
Tandem for Single Lid Cover PTS
Tandem for Double Lid Cover PTD

What type of inlet valve is required?

  Inlet Valve Type Code
  Angle Key Valve V
Angle Ball Valve B
  Angle Compression Valve G
  No Inlet Valve (subtract) -

What type of outlet valve is required?

+ (Insert Dash)
  Outlet Valve Type Code
Angle Ball Valve B
  Angle Key Valve (subtract) V
  Angle Compression Valve G
  Angle Check Valve H
  Angle Dual Check Valve HH
* Angle Cartridge Dual Check Valve HC
  No Outlet Valve (subtract) -

What meter size is required?

  Meter Size Code
  3/4" Meter 3

What type of inlet connection is required?
(See Note Below)

  3/4" Inlet Type Code
  Flared Copper 2
  PET/CTS Pack Joint 4
  Male Iron Pipe 8

What type outlet connection is required?
(See Note Below)

+ (Insert Dash)
  3/4" Outlet Type Code
  Flared Copper 2
  PET/CTS Pack Joint 4
  Male Iron Pipe 8

What pit diameter and depth is required?
Depth is measured from ground level to service line.
The service line is 2" higher than the bottom of the pit setter.
Pit Dia. & Depth Smooth Wall Tile Code **Corrugated Tile Code
20"x36" 20-36-NL **20C-36-NL
20"x48" 20-48-NL **20C-48-NL
20"x60" 20-60-NL **20C-60-NL
20"x72" 20-72-NL **20C-72-NL

Contact factory for other pit dimensions and types not listed.

* Cartridges available with enhanced chlorine/chloramine resistance. Add "CR" to the end of the alpha code. Example: PSBHCCR-388-20-36-NL.

Grip Joint - for CTS and PEP can be ordered by adding "-G" to the catalog number.

**Pitsetters manufactured from 20" corrugated tile require Ford iron covers for 21" ID Tile.

5/8"x3/4", 3/4" & 1" Setters with angle ball valve will be reduced port unless otherwise requested. Reduced port valves usually provide suitable water flow. (Add "-FP" to the catalog number for full port.) The 5/8" Port Angle Ball Valve is a one-way directional valve designed for the inlet side of the meter and should not be used as a customer shut-off on the customer side of the meter.

NOTE: Inlet and outlet connections are 3/4" in size, for 3/4" meter settings, unless otherwise specified.

Female iron pipe by Pack Joint couplings are available for a variety of inlet/outlet combinations (see Catalog Section J) and are sold separately.

The following warning applies to all Ford Meter Box products containing brass.
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
Click here for an updated listing of Ford Meter Box products pertaining to Proposition 65 lead exposure.
© 1996–2018 Ford Meter Box Company, Inc.
Ford, Ford Meter Box and Uni-Flange are trademarks of The Ford Meter Box Company, Inc. registered in the U.S.